Cloud II Series

Articles - Category Page

  • Cloud II Core Wireless Charging

    It is recommended to fully charge your headset before first use.

    مقالة قاعدة المعارف

  • دليل مستخدم شبكة Cloud II اللاسلكية

    دليل مستخدم شبكة Cloud II اللاسلكية

    مقالة قاعدة المعارف

  • Cloud II Core Wireless Pairing to Wireless Dongle

    Wireless Dongle Method 1. While the headset is off, hold the power button until the headset status LED starts blinking red/green rapidly. 2. While the wireless dongle is plugged in, use a small tool to hold down the pairing button inside the pin hole until the dongle LED starts blinking rapidly. The

    مقالة قاعدة المعارف

  • Cloud II (PlayStation® 4) Usage

    Usage (PlayStation® 4) For optimal use with PlayStation® 4 (PS4®), unplug the headset jack from the USB control box and connect audio jack on the headset directly to the PS4 game controller and follow these steps: 1. Turn on your PS4® game console. 2. Navigate to the Settings Menu and select it. 3.

    مقالة قاعدة المعارف

  • Cloud II with USB Control Box Setup

    Usage (with Control Box) Connect the headset’s 3.5mm audio jack to the input jack on the USB control box. The USB control box then connects to a computer using the USB connector on the end of the control box. To ensure that HyperX Cloud II is the default audio device, you must follow these instructi

    مقالة قاعدة المعارف

  • Cloud II Specifications

    Technical Specifications ​ Headset • Transducer type: Dynamic 53mm with Neodynium Magnets • Operating principle: Closed • Frequency response: 15Hz-25KHz (earphones) • Nominal impedance: 60 ohm per system • Nominal SPL: 98+/-3dB • T.H.D: < 2% • Power handling capacity: 150mW • Sound coupling to the e

    مقالة قاعدة المعارف

  • Cloud II Usage Direct Connect without Control Box

    Usage (Direct Connect) with No Control Box Connect your headset directly to your computer, game console, or another device (phone or tablet) that has a 3.5mm audio jack.

    مقالة قاعدة المعارف

  • Cloud II Wireless DTS Setting up DTS APO Drivers

    Plug in the USB dongle and launch NGENUITY. Click on the Headset tab. Click "Install" on the "audio Drivers Required" prompt. Wait until the drivers are finished installing. Click "OK, Will DO" on the "drivers Installed" prompt. Restart your PC.

    مقالة قاعدة المعارف

  • (HP OMEN) Cloud II Core Wireless User Manual

    (HP OMEN) Cloud II Core Wireless User Manual

    مقالة قاعدة المعارف

  • أجهزة التحكم اللاسلكية كلاود 2

    أجهزة التحكم اللاسلكية كلاود 2 مؤشر الحالة الضوئية زر الطاقة / الصوت المحيطي 7.1 اضغط مع الاستمرار لمدة 3 ثوانٍ لتشغيل/إيقاف سماعة الرأس اضغط لتشغيل/إيقاف الصوت المحيطي 7.1* *يتم إخراج الصوت المحيطي الافتراضي 7.1 كإشارة ستيريو ثنائية القناة لاستخدامها مع سماعات الرأس الاستريو. زر كتم صوت الميكروفون

    مقالة قاعدة المعارف